Magnetic Selection Tool

toolselectmagnetic

This tool, represented by a magnet over a selection border, allows you to make freeform Selections, but unlike the Polygonal Selection Tool or the Freehand Selection Tool, it will try to magnetically snap to sharp contrasts in your image, simplifying the creation of selection drastically.

There are two ways to make a magnetic selection:

../../_images/magnetic_selection_mode_1.gif

Animation showing the first mode of creating a magnetic selection.

The first is to use mouseleft and place points or nodes of the magnetic selection. To finalize your selection area you can do either mouseleft on the first created point to complete the loop and click on it again to create a selection, or press Enter to end the magnetic selection or click on the Complete button present in Tool Options.

../../_images/magnetic_selection_mode_2.gif

Animation showing the second (interactive) mode of creating a magnetic selection.

The second, interactive mode, is to mouseleft + drag over a portion of an image.

../../_images/magnetic_selection_mode_mixed.gif

The first and second mode can be mixed.

You can edit previous points by mouseleft dragging them. You can remove points by dragging it out of the canvas area. After a path is closed. Points can be undone with Shift + Z. A halfway done magnetic selection can be canceled with Esc or clicking on the Discard button in the Tool Options.

Wichtig

Most of the behavior of the Magnetic Selection Tool is common to all other selection tools, please make sure to read Selections to learn more about this tool.

Hotkeys and Sticky keys

  • Shift + mouseleft sets the subsequent selection to ‚add‘. You can release the Shift key while dragging, but it will still be set to ‚add‘. Same for the others.

  • Alt + mouseleft sets the subsequent selection to ‚subtract‘.

  • Ctrl + mouseleft sets the subsequent selection to ‚replace‘.

  • Shift + Alt + mouseleft sets the subsequent selection to ‚intersect‘.

Neu in Version 4.2:

  • Hovering your cursor over the dashed line of the selection, or marching ants as it is commonly called, turns the cursor into the move tool icon, which you mouseleft and drag to move the selection.

  • mouseright will open up a selection quick menu with amongst others the ability to edit the selection.

Menu of magnetic selection

Tipp

You can switch the behavior of the Alt key to use Ctrl instead by toggling the switch in Tool Settings in the General Settings.

Tipp

This tool is not bound to any Hotkey, if you want to define one, go to Settings ‣ Configure Krita ‣ Keyboard Shortcuts and search for ‚Magnetic Selection Tool‘, there you can select the shortcut you want. Check Shortcut Settings for more info.

Tool Options

Mode

This option is explained in the Pixel and Vector Selection Types section.

Action

This option is explained in the Pixel and Vector Selection Types section.

Anti-aliasing

This toggles whether or not to give selections feathered edges. Some people prefer hard-jagged edges for their selections.

Filter Radius:

Determine the radius of the edge detection kernel. This determines how aggressively the tool will interpret contrasts. Low values mean only the sharpest of contrast will be a seen as an edge. High values will pick up on subtle contrasts. The range of which is from 2.5 to 100.

Threshold:

From 0 to 255, how sharp your edge is, 0 is least while 255 is the most. Used in the interactive mode only.

Search Radius:

The area in which the tool will search for a sharp contrast within an image. More pixels means less precision is needed when placing the points, but this will require Krita to do more work, and thus slows down the tool.

Anchor Gap:

When using mouseleft + drag to place points automatically, this value determines the average gap between 2 anchors. Low values give high precision by placing many nodes, but this is also harder to edit afterwards. The pixels are in screen dimensions and not image dimensions, meaning it is affected by zoom.

../../_images/magnetic_selection_anchor_gap.png

To the left: 20 px anchor gap, to the right: 40px anchor gap.

Bemerkung

Anti-aliasing is only available on Pixel Selection Mode.